Surpassed rugged industry standards |
All Land Pride Rotary Cutters have been designed and tested and meet rigorous voluntary testing procedures according to ISO 4254-13. |
Factory assembled |
Arrives for quick and easy set-up. Minimal time wasted setting or prepping the unit. |
Seven Year gearbox warranty |
Shows confidence in gearbox integrity. |
Rugged heavy built gearboxes |
Capable of handling heavy cutting applications |
Gearbox seal protection |
Gearbox bottom seal protection for longer bearing life. |
Sliding guard for splitter gearbox |
Sliding guard offers protection and easy access for improved efficiency of splitter gearbox maintenance. |
Detachable shield on the wing gearbox |
Provides easy maintenance access to the driveline slip clutch and yoke. |
Two piece driveline shields |
Driveline grease zerks are easier to access. |
Low hitch weight on tractor drawbar |
Ideal for smaller hp tractors by reducing the amount of weight on the drawbar. |
Narrow A-frame tongue |
Allows for a tighter turning radius. |
Adjustable park jack angle |
Park jack can be adjusted to be perpendicular to the ground. |
Adjustable driveline support |
Serves as support rest for the driveline when the cutter is unhooked from the tractor. Assist operator when attaching driveline to the tractor power take-off shaft. |
Input driveline: Cat. 6 CV |
Driveline is matched just right for tractor capacity. Constant velocity (CV) U-joint allows for 80 degree turns without doing damage to the driveline. |
Drivelines with slip-clutches: Cat. 5 intermediate Cat. 4 or Cat. 5 wing |
Driveline is sized right for the intended cutting capacity. Slip-clutches will slip under load to minimize twist damage to driveline profiles. |
Grease zerks on end caps of driveline |
Intermediate and wing driveline cross journals are easier to grease. |
High blade tip speed |
Allows clean cutting of material. |
6" Blade overlap |
Eliminates skipping during turns. |
Forged blade bar (Optional) |
Provides the critical strength needed for consistent, top performance. |
3/16" Round stump jumper (Optional) |
Standard thick stump jumper material keeps damage to a minimum. |
Smooth top design |
Reduces accumulation of debris and is easier and faster to clean. |
Tops of decks are 100% welded |
Makes center and wing decks stronger. |
Deck Armor™ (Optional) |
Reduces deck damage from blade to deck contact without affecting cut quality. |
Replaceable 1/4" side skirt thickness |
Increased thickness reduces damage from objects thrown into the side skirt. |
Multiple center skid shoe locations |
Run two skid shoes under the hitch pivots or two skid shoes under the wing hinges. |
Beveled skid shoes on the wing & weight box |
Reduces gouging the ground when turning. |
LED signal lights |
LED lights are bright, long lasting, and resist vibration, unlike incandescent lights. |
Wire harness 7-pin plug holder |
Spring hose loop mounted holder keeps wire harness plug out of the dirt and rain. |
Hinged wing section |
Allows the cutter to follow the terrain. Ideal for rough ground where hillsides, ditches, and hollows can cause uneven cutting |
1" Solid hinge rods |
Larger diameter hinge rod provides greater strength in the hinge area. |
Wing transport lock pin |
Transport lock pin holds the wing in the folded position in the event of hydraulic loss. |
Enclosed dual 1" leveling rods |
Cutter pulls equally on the rear axle while traveling over rough terrain. |
Five-bolt hubs with larger bearings, five lip hub seals, and bolted-on hub caps |
Makes the wheel assembly more durable and longer lasting. Five hub seals make it harder for water & debris to enter the hub and grease to leave the hub. Hub caps cannot be knocked off by foreign material. |
Drain holes in wheel rims |
Allows water to drain from wheels mounted on the folded-up wing. Helps prevent paint deterioration and rusting to the wheel rims. |
Replaceable individual wheel spindles |
Spindles can be replaced when damaged without replacing entire axle assembly. |
Wheel options |
Laminated tires: Eliminates flats. Air-filled tires: Give better cushion while transporting. Foam-filled tires: Give better cushion while transporting and can’t go flat. |
LP Performance Hitch™ (Optional) |
One person Hook-up. Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and pivots about the tractor drawbar up to 12 degrees in both left and right directions. |
Bar-Tite hitch (Optional) |
Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear. |
Maintenance free tongue & axle pivots |
Self lubricating journal bearings make for less maintenance. |
Color-coded hydraulic hose handles |
Easy hose identification & sturdy handle to easily connect & disconnect from tractor. |
Hydraulic hose holders |
Tongue mounted hose holder keeps hose tips out of the dirt. |
Greasable cast steel, continuous hinges |
Cast steel hinges make a strong connection & are easy to lubricate. |
Center axle options |
HD Single suspension center axle: Spring cushion at the cylinder for cushion with least amount of moving parts. Independent suspension wing axles: Offers additional suspension support on the wing axle. Walking tandem center axle: Designed for versatility over a multitude of terrains. Parallel pivot center axle: Provides unmatched ground contact for hill-like terrains. |
Wing axle option |
HD Single suspension wing axles: One piece wing axle that gets support from the center cylinder spring cushioning on the center axle for cushioning with the least amount of moving parts. Independent suspension wing axle: Offers additional suspension support on the wing axle. Walking tandem wing axle: Designed for versatility over a multitude of terrains. Parallel pivot axle: Provides unmatched ground contact for hill-like terrains. |
Dual-acting fold cylinder (Optional) |
Allows for a narrow transport width of 7'-3" (2.21 m). |
Flip spacers |
Easily change cut height with a flip of a spacer. |
SMV Mounting Socket (Standard) SMV Sign (Accessory) |
SMV mounting socket receives most SMV signs equipped with a mounting blade for ease of attachment and removal when transporting on a truck or trailer. SMV sign is offered as an accessory when the tractor’s SMV sign and mounting blade does not fit the cutter’s standard SMV mounting socket. |